Description
Product Overview
The Kollmorgen CP310250 is an industrial servo-drive designation associated with the SERVOSTAR SP motion-control platform. A servo amplifier regulates motor current in response to commands from a motion controller and feedback from the connected motor. Depending on the installed configuration, this control architecture supports position, speed, and torque regulation for automated machinery. Typical applications include machine tools, packaging equipment, indexing mechanisms, and production systems that require repeatable motion and controlled acceleration or deceleration.
Correct identification is essential when replacing this legacy drive. The CP310 family includes different electrical configurations, and the complete part number can specify important differences in power supply, logic-power arrangement, and hardware options. Available documentation for the CP310 platform identifies a 10 A continuous-current class and a 20 A peak-current rating for the relevant configuration, but these values should not be applied to an unidentified unit without checking its full designation and rating label. The Kollmorgen CP310250 should be matched to the original drive, motor, feedback device, and controller interface before a replacement is approved.
For maintenance engineers, retaining a compatible servo amplifier can reduce the work involved in restoring a machine axis. Before installation, compare the motor’s rated current and voltage, feedback wiring, command interface, and drive parameters with the original setup. Confirm that the required configuration software and parameter backup are available. After replacement, qualified personnel should check motor identification, feedback direction, control-loop behavior, fault handling, and motion limits before returning the machine to production. When sourcing a legacy unit, request photographs of the complete nameplate and available functional-test records rather than relying on the shortened model number alone.
Product Introduction
A servo-drive replacement must match the motor, feedback device, and power configuration—not just the front-panel designation. The Kollmorgen CP310250 is associated with the SERVOSTAR SP servo-drive family for closed-loop industrial motion control.
Verify the complete part number, current rating, supply voltage, and feedback interface before ordering. Parameter backup and controlled commissioning are important when restoring an established machine axis.
Key Technical Specifications
| Parameter | Value |
|---|---|
| Product Model | CP310250 |
| Manufacturer | Kollmorgen |
| Product Family | SERVOSTAR SP / CP310 |
| Product Type | Digital servo amplifier / servo drive |
| Primary Function | Closed-loop motor motion control |
| Control Modes | Position, speed, and torque control, subject to configuration |
| Continuous Output Current | 10 A for the documented CP310 configuration; verify exact unit |
| Peak Output Current | 20 A for the documented CP310 configuration; verify permitted duration and exact unit |
| Supply Voltage | Confirm the complete model designation and nameplate |
| Motor Compatibility | Verify motor ratings and supported feedback device |
| Feedback Interface | Depends on the drive configuration |
| Communication Interface | Verify against the complete part number and installed controller |
| Mounting | Cabinet installation; confirm dimensions and clearances |
| Cooling Requirements | Confirm from the applicable manual |
| Operating Temperature | Verify from the exact model documentation |
| Hardware Revision | Check the individual unit label |
| Condition | Confirm new, surplus, refurbished, or used status |
Specification note: Public listings contain conflicting electrical details for CP310250. The table separates family-level information from parameters that require confirmation. Do not use these values for electrical design or commissioning without checking the applicable Kollmorgen manual and drive nameplate.
CP310250
Related Products
- CP303 — Earlier SERVOSTAR SP family drive with a different current class; assess the motor and application requirements before considering substitution.
- CP306 — Related SERVOSTAR SP drive configuration; compare electrical ratings and hardware options.
- CP310 — Related drive designation documented in the SERVOSTAR SP manual; the complete model code determines its configuration.
- PRD-P310250Z-55 — Full designation associated with CP310250 in supplier listings; confirm the actual nameplate before treating it as the same unit.
- PRD-P310250E-55 — Related full designation appearing in supplier documentation; verify suffix-specific configuration and interchangeability.
- Kollmorgen AKM Servo Motors — Servo motor family that may be used in compatible motion systems; verify the drive’s supported motor and feedback combination.
- Kollmorgen Silverline Servo Motors — Another motor family referenced with SERVOSTAR SP applications; confirm electrical and feedback compatibility.
- Compatible Motor Feedback Cable — Select according to the actual motor feedback device and drive connector arrangement.
These are related family references, not guaranteed drop-in replacements. Confirm voltage, current, feedback type, communication interface, mounting, and parameter compatibility before substituting a different model.
Frequently Asked Questions
1. What is the Kollmorgen used for?
It is associated with the SERVOSTAR SP servo-drive family and provides controlled motor operation in industrial motion systems. The precise capabilities depend on the full drive configuration and connected motor.
2. Is the a 250 A servo drive?
Do not infer a 250 A output rating from the model number. Documentation for the relevant configuration identifies a 10 A continuous-current class and a 20 A peak-current rating. Verify the complete part number and nameplate before relying on any rating.
3. Can I replace a with a CP306 or CP303?
Not without an engineering compatibility check. These related drive configurations may have different current ratings and electrical requirements. Compare the motor specification, power supply, feedback interface, and control architecture before approving a replacement.
4. Can I hot-swap the ?
Do not assume live replacement is supported. Isolate the drive according to the applicable safety procedure, allow the DC bus to discharge as specified by the manufacturer, and verify the safe state before handling power connections.
5. Will the original servo parameters transfer to a replacement?
Not automatically. Parameter compatibility depends on the drive variant, firmware, configuration software, motor, and feedback device. Back up the original parameters where possible and confirm the transfer procedure before commissioning.
6. How can I verify a replacement drive’s condition?
Check the full model code, serial label, terminals, connectors, and visible signs of damage or repair. Request a functional-test report and written warranty terms. A visual inspection alone does not establish that the drive can operate a motor correctly under load.
7. What information should I provide when sourcing a replacement?
Provide the full nameplate designation, supply and motor ratings, feedback type, controller interface, hardware revision, and any available parameter backup. This helps establish whether the replacement is electrically and functionally compatible with the installed servo axis.
